ในวงการอุตสาหกรรมเป็นที่ยอมรับโดยทั่วไปว่าการวิเคราะห์ค่าความสั่นสะเทือนของเครื่องจักร
สามารถบอกถึงปัญหาของเครื่องจักรได้ครอบคลุมที่สุด
โดยแต่ละโรงงานควรใช้ความสั่นสะเทือนเป็นมาตรฐานหลักในการระบุปัญหาของเครื่องจักร
ค่าความสั่นสะเทือนของเครื่องจักร สามารถบ่งบอกปัญหาทางกลหลายชนิด เช่น
การหมุนที่ไม่สมดุล การเยื้องศูนย์ การสึกหรอของชิ้นส่วนต่างๆ ฯลฯ
ในขณะที่ค่าความสั่นสะเทือนของตลับลูกปืน จะบ่งบอกถึงปัญหาในการหล่อลื่น ฝุ่นผง
การติดตั้งตลับลูกปืน รวมถึงความล้าของตัวตลับลูกปืนเอง ในส่วนของงานซ่อมบำรุงนั้น เราสามารถพิจารณาเกณฑ์การสั่นสะเทือนสำหรับเครื่องจักรกลหมุน โดยจะถูกกำหนดโดยมาตรฐานสากล องค์การมาตรฐาน ISO - 2372 (10816) แบ่งเป็นเกณฑ์การพิจารณา4ลักษณะ (4Class) ดังที่แสดงอยู่ในตารางนี้
ISO 10816 Vibration Severity Standards
ISO 2372 (10816) Standards provide guidance for evaluating vibration severity in machines operating in the 10 to 200Hz (600 to 12,000 RPM) frequency range. Examples of these types of machines are small, direct-coupled, electric motors and pumps, production motors, medium motors, generators, steam and gas turbines, turbo-compressors, turbo-pumps and fans. Some of these machines can be coupled rigidly or flexibly, or connected though gears. The axis of the rotating shaft may be horizontal, vertical or inclined at any angle. Use the chart below combined with additional factors described in this manual to judge the overall vibration severity of your equipment.
Vibration Criteria Vibration Limites for rotating machines are defined by the International Standards Organization, ISO-2372 and are on the table Class I< 15kW. Class II> 15kW. Class III> 100kW. Class IV> 100kW.
A - New machine condition ( Good ) B - Long-term operation allowable ( Satisfactory ) C - Short-term operation allowabale ( Unsatisfactory ) D - Vibration causes Damage
ในการตรวจเช็คค่าความสั่นสะเทือนเพื่อบันทึกลง Vibration test Report
ทำการวัดทั้งหมด6ตำแหน่ง ดังนี้ 1
ด้านหน้าและด้านหลังตามแนวแกน 2
วัดด้านข้างที่ตำแหน่งด้านหน้าและด้านหลัง 3
วัดด้านบนที่ตำแหน่งด้านหน้าและด้านหลัง
Vibration test Report
At Speed |
rpm. |
Vertical |
Horizontal |
Axial |
Direction |
Bearing No: |
mm./s. |
mm./s. |
mm./s. |
D-End |
|
|
|
|
ND-End |
|
|
|
|
Copyright © 2003. All rights reserved www.savemotor.com Web master : 086-667-8789 Download |